SizeGenetics was developed and launched by a team of leading Danish scientists, with the intention of becoming the world’s first universally effective and medically-approved penis enlargement device.
SizeGenetics uses a traction enlargement mechanism, which follows the same basic principles as those that apply to weight-lifting. The gentle yet constant traction applied to the penis stimulates the natural process of cell multiplication within the penis, ultimately leading to increased size and strength.
SizeGenetics has been designed to effectively lengthen the penis on a permanent basis, without adversely affecting circumference. On average, users of the SizeGenetics experienced penis growth (while erect) of approximately 2.8% after the initial four-months treatment period.
An average improvement of 24%. SizeGenetics does not to adversely affect sexual performance or urination and can be used for up to 12 hours daily for maximum results.
Description Of Components And Assembly Instructions
The SizeGenetics device consists of a basal plastic ring (1) with a recess for the urethra (2). The ring is attached to the base of the penis. Two metal bars, one with a right-handed thread (3), the other with a left-handed thread (4) are connected to the basal ring. Hidden inside each bar is a spring contrivance (5).
At the distal end, the two bars are connected to a plastic support (6) with two holes, through which the ends of a silicone tube are passed and 2 slots for the Comfort Strap (Not Pictured Here). The device comes with components 1-5 already assembled for convenience.
Depending on how large or small the penis is, the user may choose the short or the long extension bars which can be attached and detached using the round spanners included in the kit.
You should set the SizeGenetics to precisely one centimetre longer than the length of your stretched flaccid penis before using it. This will mean attaching the required lengthening bars to the extender by screwing them into the metal bars on either side of the unit.
You will need the additional extension bars at a later stage as your penis begins to grow. The plastic support (6) is attached by passing the ends of the bars (5) into the two larger holes of the support.
The support is then pressed towards the basal ring (1). The springs are thus pressed home. Press firmly until a snap or a click indicates that the support is firmly secured to the bars.
Instructions For Attaching
SizeGenetics is attached to the penis by fastening the basal ring (1) around the bottom of the shaft, so that the two metal bars (2) run parallel with the penis on either side and the head of the penis is placed in the bowl-shaped support (3).
Pass the two ends of the silicone tube/comfort strap (not pictured here) through the holes in the plastic support (4) to create a loop through which the head of the penis is passed. Before locking the device in place, the plastic support should be pressed towards the body so that the two springs press home.
The silicone tube or the comfort strap (5) is fastened around the penis head by pulling the ends accordingly. If you are using the silicone noose, you can secure these in place (6) on the reverse side of the support.
SizeGenetics Protection Pad Accessory
In some instances, the initial exertion of force upon the penis can lead to mild and temporary soreness. Should this occur, SizeGenetics is supplied with the protection pad accessory to maximise comfort. If necessary, slowly expand the protection pad and position behind the glans of the penis, ensuring a snug and secure fit.
The SizeGenetics extender can then be used as normal. For maximum comfort, it is recommended that the initial force applied to the penis be kept below 900g for a maximum of 8 hours during the initial six weeks. Should additional protection pads be required, these can be purchased quickly and easily from the SizeGenetics manufacturer.
Adjusting the SizeGenetics Extender
It is strongly advised that you do NOT try to change the traction setting of your device for the first six weeks. When it becomes necessary to make adjustments, it is simply a case of using the two thumb-screws to increase traction by turning them inwards.
In order to ensure that the change is made correctly, it’s important to note the following:
- You must be wearing the device at the time you make the adjustment, to ensure that the traction level is appropriate and comfortable.
- Always ensure your SizeGenetics has been set to the correct length.
- Make adjustments when your penis is flaccid and outstretched.
You can see the level of force that will be exerted on the penis on the hexagon pistons – settings available include 600g to 900g and 1200g to 1500g. Each marking is representing a traction force of 300g.
Out of the box, the SizeGenetics is set to exert the minimum 600g of force initially, which is the ideal starting traction.
Week One – Use SizeGenetics for 2 to 3 hours per day with a traction setting of 600g to 900g max.
Week Two – SizeGenetics can be used for up to 4 hours per day with the same traction force.
Week Three – Use SizeGenetics for 4 to 5 hours daily with maximum traction of 600g to 900g.
Week Four – Increase to 5 or 6 hours per day while keeping the same traction setting.
Week Five – Same traction setting, though increase use to 6 or 7 hours per day.
Week Six – Use SizeGenetics for 7 to 8 hours per day with the same traction setting.
Week Seven Onwards – Use SizeGenetics for 8 to 12 hours daily for maximum benefit, with traction between 900g and 1200g.
Always remember to remove your SizeGenetics extender at least once every 2 hours to allow healthy blood flow into the penis.
Detaching the SizeGenetics Extender
While the SizeGenetics extender is in use, the penis can be held in any position apart from sideways. While wearing relatively loose-fitting trousers, SizeGenetics has been designed to be relatively inconspicuous.
In order to prevent premature detachment or uncomfortable positioning, it is not recommended that the SizeGenetics extended be worn while sleeping. Should you develop an erection while using SizeGenetics, the device should be removed and reattached at a later time.
SizeGenetics can be easily removed by simply loosening the comfort strap or silicon tube, after which the penis can be removed with ease. Ensure you keep your SizeGenetics extender hygienically clean at all times, washing it with soap and water on a daily basis and disinfecting periodically with a mild, dilute alcohol solution.